media: iris: add support for purwa platform#914
Open
WangaoW wants to merge 18 commits intoqualcomm-linux:tech/all/dt/hamoafrom
Open
media: iris: add support for purwa platform#914WangaoW wants to merge 18 commits intoqualcomm-linux:tech/all/dt/hamoafrom
WangaoW wants to merge 18 commits intoqualcomm-linux:tech/all/dt/hamoafrom
Conversation
Add in two CCI buses. One bus has two CCI bus master pinouts: cci_i2c_sda0 = gpio101 cci_i2c_scl0 = gpio102 cci_i2c_sda1 = gpio103 cci_i2c_scl1 = gpio104 The second bus has two CCI bus master pinouts: cci_i2c_sda2 = gpio105 cci_i2c_scl2 = gpio106 aon_cci_i2c_sda3 = gpio235 aon_cci_i2c_scl3 = gpio236 Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Christopher Obbard <christopher.obbard@linaro.org> Tested-by: Christopher Obbard <christopher.obbard@linaro.org> Link: https://lore.kernel.org/all/20260226-x1e-camss-csi2-phy-dtsi-v1-2-f3f7ddfbf849@linaro.org/
Add csiphy nodes for - csiphy0 - csiphy1 - csiphy2 - csiphy4 The irregular naming of the PHYs comes directly from the hardware which for whatever reason skipped csiphy3. Separating the nodes from CAMSS as we have done with the sensor I2C bus aka the CCI interface is justified since the CSIPHYs have their own pinouts and voltage rails. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Christopher Obbard <christopher.obbard@linaro.org> Tested-by: Christopher Obbard <christopher.obbard@linaro.org> Link: https://lore.kernel.org/all/20260226-x1e-camss-csi2-phy-dtsi-v1-3-f3f7ddfbf849@linaro.org/
Add dtsi to describe the xe180100 CAMSS block 4 x CSIPHY 3 x TPG 2 x CSID 2 x CSID Lite 2 x IFE 2 x IFE Lite Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Link: https://lore.kernel.org/all/20260226-x1e-camss-csi2-phy-dtsi-v1-4-f3f7ddfbf849@linaro.org/
…gulators Add pmic,id = m rpmh to regulator definitions. This regulator set provides vreg_l3m_1p8 the regulator for the ov08x40 RGB sensor on the CRD. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Christopher Obbard <christopher.obbard@linaro.org> Link: https://lore.kernel.org/all/20260226-x1e-camss-csi2-phy-dtsi-v1-5-f3f7ddfbf849@linaro.org/
…SIPHY4 Define ov08x40 on cci1_i2c1. The RGB sensor appears on the AON CCI pins connected to CSIPHY4 in four lane mode. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Christopher Obbard <christopher.obbard@linaro.org> Link: https://lore.kernel.org/all/20260226-x1e-camss-csi2-phy-dtsi-v1-6-f3f7ddfbf849@linaro.org/
…h voltage levels for IR and RGB camera Add the PM8010 PMIC providing the following voltage rails: vreg_l1m_r @ 1v2 IR sensor vreg_l2m_r @ 1v2 RGB sensor vreg_l3m_r @ 1v8 IR sensor vreg_l4m_r @ 1v8 RGB sensor vreg_l5m_r @ 2v8 IR sensor vreg_l7m_r @ 2v8 RGB sensor Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Link: https://lore.kernel.org/all/20260226-x1e-camss-csi2-phy-dtsi-v1-7-f3f7ddfbf849@linaro.org/
…on CSIPHY4 Switch on the ov02c10 RGB sensor on CSIPHY4. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Christopher Obbard <christopher.obbard@linaro.org> Tested-by: Christopher Obbard <christopher.obbard@linaro.org> Link: https://lore.kernel.org/all/20260226-x1e-camss-csi2-phy-dtsi-v1-8-f3f7ddfbf849@linaro.org/
…amera PMIC with voltage levels for IR and RGB camera Add voltage regulators-8 for Camera on slim7x including: - vreg_l7m_2p8 - vreg_l2m_1p2 - vreg_l4m_1p8 Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Christopher Obbard <christopher.obbard@linaro.or> Link: https://lore.kernel.org/all/20260226-x1e-camss-csi2-phy-dtsi-v1-9-f3f7ddfbf849@linaro.org/
Add pm8010 L4M regulator which is used by Camera I2C pull-up. Signed-off-by: Tingguo Cheng <tingguo.cheng@oss.qualcomm.com> Signed-off-by: Wenmeng Liu <wenmeng.liu@oss.qualcomm.com> Link: https://lore.kernel.org/all/20260227-hamoa_evk-v1-1-36f895a24d8f@oss.qualcomm.com/
Enable IMX577 via CCI on Hamoa EVK Core Kit. The Hamoa EVK board does not include a camera sensor by default, this DTSO has enabled the Arducam 12.3MP IMX577 Mini Camera Module on the CSI-1 interface. Signed-off-by: Wenmeng Liu <wenmeng.liu@oss.qualcomm.com> Link: https://lore.kernel.org/all/20260227-hamoa_evk-v1-2-36f895a24d8f@oss.qualcomm.com/
…configuration Hamoa IOT boards support a different thermal junction temperature specification compared to the base Hamoa platform due to package level differences. Update the passive trip thresholds to 105°C to align with the higher temperature specification. Signed-off-by: Gaurav Kohli <gaurav.kohli@oss.qualcomm.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Link: https://lore.kernel.org/linux-devicetree/20260302-higher_tj-v1-1-4c0d288f8e7f@oss.qualcomm.com/
Enable UFS for purwa-iot-evk board. This patch depends on [PATCH V5 2/3] arm64: dts: qcom: hamoa: Add UFS nodes for x1e80100 SoC https://lore.kernel.org/all/20260211132926.3716716-3-pradeep.pragallapati@oss.qualcomm.com/ Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/all/20260323-purwa-ufs-v2-1-58fb2c168786@oss.qualcomm.com/ Signed-off-by: Pradeep P V K <pradeep.pragallapati@oss.qualcomm.com>
…t evk board Enable SD Card host controller for purwa iot evk board. Signed-off-by: Sarthak Garg <sarthak.garg@oss.qualcomm.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/20260323110017.2527956-1-sarthak.garg@oss.qualcomm.com Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Pradeep P V K <pradeep.pragallapati@oss.qualcomm.com>
…vice Interconnect from SCM device are optional and were added to get additional performance benefit. These nodes however delays the SCM firmware device probe due to dependency on interconnect and results in NULL pointer dereference for the users of SCM device driver APIs, such as PDC driver. Remove them from the scm device to unblock the user. Link: https://lore.kernel.org/r/20260312-hamoa_pdc-v1-1-760c8593ce50@oss.qualcomm.com Signed-off-by: Maulik Shah <maulik.shah@oss.qualcomm.com> Signed-off-by: Sneh Mankad <sneh.mankad@oss.qualcomm.com>
Add deepest idle state along with pdc config reg to make GPIO IRQs work as wakeup capable interrupts in deepest idle state. Add QMP handle to allow PDC device to place a SoC level low power mode restriction. Link: https://lore.kernel.org/r/20260312-hamoa_pdc-v1-4-760c8593ce50@oss.qualcomm.com Signed-off-by: Maulik Shah <maulik.shah@oss.qualcomm.com> Signed-off-by: Sneh Mankad <sneh.mankad@oss.qualcomm.com>
Purwa shares the Hamoa (X1E80100) PDC device, but the hardware register bug addressed in commit e9a48ea ("irqchip/qcom-pdc: Workaround hardware register bug on X1E80100") is already fixed in Purwa silicon. Hamoa compatible forces the software workaround. Use the Purwa specific compatible string for the PDC node to remove the workaround from Purwa. Fixes: f08edb5 ("arm64: dts: qcom: Add X1P42100 SoC and CRD") Link: https://lore.kernel.org/r/20251231-purwa_pdc-v1-2-2b4979dd88ad@oss.qualcomm.com Signed-off-by: Maulik Shah <maulik.shah@oss.qualcomm.com> Signed-off-by: Sneh Mankad <sneh.mankad@oss.qualcomm.com>
… points The Iris block on X1P differs from SM8550/X1E in its clock configuration and requires a dedicated OPP table. The node inherited from the X1E cannot be reused directly, and the fallback compatible "qcom,sm8550-iris" cannot be applied. Override the inherited clocks, clock-names, and operating points, and replaces them with the X1P42100-specific definitions. A new OPP table is provided to support the correct performance levels on this platform. Link: https://lore.kernel.org/linux-arm-msm/20260401-enable_iris_on_purwa-v4-4-ca784552a3e9@oss.qualcomm.com/ Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Signed-off-by: Wangao Wang <wangao.wang@oss.qualcomm.com>
Enable video nodes on the purwa-iot-som board. Link: https://lore.kernel.org/linux-arm-msm/20260401-enable_iris_on_purwa-v4-5-ca784552a3e9@oss.qualcomm.com/ Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Signed-off-by: Wangao Wang <wangao.wang@oss.qualcomm.com>
jiegan0107
force-pushed
the
tech/all/dt/hamoa
branch
from
858f8a4 to
cefc782
Compare
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
8 participants
Add this suggestion to a batch that can be applied as a single commit.This suggestion is invalid because no changes were made to the code.Suggestions cannot be applied while the pull request is closed.Suggestions cannot be applied while viewing a subset of changes.Only one suggestion per line can be applied in a batch.Add this suggestion to a batch that can be applied as a single commit.Applying suggestions on deleted lines is not supported.You must change the existing code in this line in order to create a valid suggestion.Outdated suggestions cannot be applied.This suggestion has been applied or marked resolved.Suggestions cannot be applied from pending reviews.Suggestions cannot be applied on multi-line comments.Suggestions cannot be applied while the pull request is queued to merge.Suggestion cannot be applied right now. Please check back later.
This series enables the Iris video codec on purwa, allowing purwa to
use hardware‑accelerated video encoding and decoding.
The Iris codec on purwa is nearly identical to the one on hamoa(X1E),
except that it requires one additional clock and uses a different OPP
table.
Therefore, purwa can reuse the Iris node from hamoa, but the clocks
and OPP table need to be redefined.
All patches have been tested with v4l2-compliance and v4l2-ctl on
purwa. And it does not affect existing targets.