Skip to content

PID request for USB Sniffer 2 (1209:6688) - #1223

Merged
tannewt merged 2 commits into
pidcodes:masterfrom
vllogic:master
Nov 19, 2026
Merged

tannewt merged 2 commits into
pidcodes:masterfrom
vllogic:master

Conversation

@talpachen

@talpachen talpachen commented Jun 9, 2026 •

Copy link
Copy Markdown
Contributor

USB 2.0 protocol analysis (USB 3.0 communication)

  1. Firmware and host tool source code:
    https://github.com/vllogic/ataradov.usb-sniffer

    • License: BSD-3-Clause
    • Build: open-source SDCC compiler (see firmware/Makefile)
  2. KiCad schematic and PCB files:
    https://github.com/vllogic/dalishen_pi_h7p20/tree/main/hardware/usb_sniffer_2

    • License: GPLv3
  3. FPGA logic:
    https://github.com/vllogic/dalishen_pi_h7p20/tree/main/examples/usb_sniffer_h7p20.ataradov.usb_sniffer

    • License: BSD-3-Clause

All software required to build and use the device is open source. The firmware
and host tool are a fork of the open-source project ataradov/usb-sniffer.

PID 1209:6688 is used by the USB Sniffer 2 firmware when the device enumerates.

Full documentation (software, firmware, licenses and build instructions):
https://github.com/vllogic/dalishen_pi_h7p20/blob/main/hardware/usb_sniffer_2/readme.md

@cnlohr

cnlohr commented Aug 10, 2026

Copy link
Copy Markdown
Collaborator

@talpachen can you make it clear which software this PID code goes to inside the PR or on the page? It's not clear what software packages are needed and if all of them are open source.

@talpachen

Copy link
Copy Markdown
Contributor Author

@talpachen can you make it clear which software this PID code goes to inside the PR or on the page? It's not clear what software packages are needed and if all of them are open source.

@cnlohr
This PID (0x1209:0x6688) applies to:

Host tool usb_sniffer (same repo, software/ directory) — BSD-3-Clause

The FPGA logic code and the hardware design are also open source; links are above.

@cnlohr

cnlohr commented Sep 28, 2026

Copy link
Copy Markdown
Collaborator

@talpachen
Please add the details to the readme linked in the PR, i.e. site: should point to a README where all of this is addressed. Comments in this thread are not retained in tree history.

@talpachen

Copy link
Copy Markdown
Contributor Author

@cnlohr

Done. The details are now in the README that site points to:

https://github.com/vllogic/dalishen_pi_h7p20/blob/main/hardware/usb_sniffer_2/readme.md

It covers the firmware, host tool, FPGA logic, build toolchain (SDCC) and
licenses (BSD-3-Clause for software/FPGA, GPLv3 for hardware). I also added the
source: field, and site: now points directly at the README. All required
software is open source.

Please take another look.

@newtbot-tannewt

Copy link
Copy Markdown

Automated LLM review run and checked by tannewt at 2026-11-19 19:52:50 UTC:

Sources: FX2LP SDCC C firmware source (firmware/ of vllogic ataradov.usb-sniffer fork); Hercules Fuxi Verilog FPGA logic source for USB Sniffer 2; USB Sniffer 2 KiCad schematic and PCB (hardware/usb_sniffer_2).

Third-party device: The sniffer still relies on Cypress/Microchip EZ-USB CY7C68013A (FX2LP) hardware: the firmware PID is carried by FX2LP firmware, and the usb_sniffer_2 README only lists HME H7P20N0L128-M3H1, WCH CH32H417 and Microchip USB3343 as on-board parts, describing the CH32H417 as removing 'the speed bottleneck of the 68013'. The sibling Dalishen Pi README describes connecting an external ~CNY 20 EZ-USB CY7A68013A board (with a Taobao purchase link) to obtain USB sniffer function, and the whole design is a port of Alex Taradov's upstream usb-sniffer (CY7C68013A + Lattice LCMXO2 + Microchip USB3343, whose KiCad design is in hardware/usb-sniffer.kicad_sch/.kicad_pcb). (evidence, evidence, evidence, evidence, evidence)

Investigation details

PR 1223 registers PID 1209:6688 for the vllogic 'USB Sniffer 2'. The site: README (hardware/usb_sniffer_2/readme.md) and source: repo give direct links to editable KiCad 9.0.6 hardware (schematic sheets + PCB, GPLv3) and to the BSD-3-Clause C firmware for the FX2LP bridge built with SDCC, plus BSD-3-Clause Verilog FPGA logic ported from ataradov/usb-sniffer. Both firmware and hardware sources exist and are open. Collaborator cnlohr's request (put the software/license details into the README that site: points to) was addressed by author commit 8393539 ('Add source and software details for PID 1209:6688') and the author's 2026-11-05 reply, so no close suggestion. Caveat: the fetched upstream descriptors still declare 0x6666:0x6620, so the exact 1209:6688 value is not visible in the fetched descriptor file.

Firmware

Hardware

Source discovery paths

PR #1223: PID request for USB Sniffer 2 (1209:6688) n1
└── 1209/6688/index.md: USB Sniffer 2 (changed PID registration) n2
├── source: https://github.com/vllogic/dalishen_pi_h7p20 — from PR front matter (source) n3
│ └── vllogic/dalishen_pi_h7p20 — 243 files (repository inspection) n18
│ ├── USB Sniffer 2 KiCad schematic and PCB (hardware/usb_sniffer_2) — source folder (Hardware-design path or file extension) n34
│ └── Hercules Fuxi Verilog FPGA logic source for USB Sniffer 2 — listed in repository tree (Project documentation may link to sources) n145
└── site: https://github.com/vllogic/dalishen_pi_h7p20/blob/main/hardware/usb_sniffer_2/readme.md — from PR front matter (site) n4
└── hardware/usb_sniffer_2/readme.md — content fetched (content verification) n7
└── ataradov/usb-sniffer — linked from evidence (outbound link) n13
└── ataradov/usb-sniffer — 66 files (repository inspection) n157
└── FX2LP SDCC C firmware source (firmware/ of vllogic ataradov.usb-sniffer fork) — source folder (Firmware path, source extension, or build metadata) n186

@tannewt
tannewt merged commit 3ad6685 into pidcodes:master Nov 19, 2026
2 checks passed
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment

Labels

None yet

Projects

None yet

Development

Successfully merging this pull request may close these issues.

4 participants