Skip to content

Pull resistors at 1.8 V on firmware with la_pull_1v8 - #117

Merged
wardviaene merged 1 commit into
mainfrom
pulls-1v8
Nov 19, 2026
Merged

wardviaene merged 1 commit into
mainfrom
pulls-1v8

Conversation

@wardviaene

Copy link
Copy Markdown
Member

Follows benchpod-firmware's la_pull_1v8 feature (features revision 4): v3 boards pull LA1-LA6 up to the LA bank rail, so the pod's pulls work at 1.8 V.

  • SDK: power_on applies a 1.8 V profile's pulls, and expansion(pullups="pod") (also its default) works at 1.8 V, when the pod has the feature (BenchPod._pulls_at). Older firmware behaves as before; power_on now logs that the pulls stay off.
  • The Wiring warning for pulls with la_mv 1800 names the firmware it needs.
  • rev3 e2e: test_pulls_at_1v8 (pull kept across the switch, engaged at 1.8 V, line high) and test_pull_down_at_1v8; on older firmware it still checks the old release/refusal.
  • MCP: set_pull, power_on, i2c_open, expansion and the guide no longer say 3.3 V only. tools_surface.json refreshed.
  • Feature map synced (revision 4). CHANGELOG Unreleased entries.

Tests: SDK 1005 passed (with BENCHPOD_FIRMWARE_DIR on the firmware branch; test_bundled_copy_matches_the_firmware fails against firmware main until the firmware PR merges), MCP 209, openhtf 74, scripts 12. HW results to follow in a comment.

🤖 Generated with Claude Code

@wardviaene

Copy link
Copy Markdown
Member Author

HW on benchpod-30a9f1 (analog v3r2), dev build of embeddedci-com/benchpod-firmware#170. The DUT stayed unpowered (it is a 3.3 V board).

  • Published 3.10.12 baseline: at 1.8 V pullups_available is 0 and pull:"up" is refused ("3V3-referenced").
  • Dev build: with LA1/LA2 up at 3.3 V, the switch to 1.8 V keeps them on (mask 3), the lines stay high and the bank reads back 1.8 V.
  • At 1.8 V: LA1 off then up again (state up, 4.7k, pullups_available 1), LA6 up (line reads 1), LA7 down (line reads 0). LA7 up gives BP0024, LA9 up gives BP0023.
  • I2C master at 1.8 V on LA1/LA2 with pullups="pod": starts, the scan is clean (nothing powered), the lines idle high. Without the pulls it is refused as before.
  • UART RX hold at 1.8 V: the LA3 pull-up is on during the session and off after.
  • SDK e2e on Pull resistors at 1.8 V on firmware with la_pull_1v8 #117 (rev3, gpio and pod tiers, including the new test_pulls_at_1v8 and test_pull_down_at_1v8): 111 passed, 12 skipped (fixtures not wired).
  • Not measured: the absolute voltage at the pin. No DMM or ADC sits on an LA line on this bench, so the 1.8 V level comes from the netlist (the pull-ups go to LA_VCCIO) and the bank readback.

The pod is restored to published 3.10.12.

SDK: power_on applies a 1.8 V profile's pulls and expansion(pullups="pod") works at
1.8 V when the pod has the la_pull_1v8 feature (BenchPod._pulls_at); older firmware
behaves as before and power_on logs that the pulls stay off. Wiring warning, README,
rev3 e2e (pulls kept across the switch, pull-up and pull-down at 1.8 V) and feature map
(revision 4) updated. MCP: set_pull, power_on, i2c_open, expansion and the guide no
longer say 3.3 V only.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
@wardviaene
wardviaene merged commit 1043109 into main Nov 19, 2026
20 checks passed
@wardviaene
wardviaene deleted the pulls-1v8 branch November 19, 2026 04:08
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment

Labels

None yet

Projects

None yet

Development

Successfully merging this pull request may close these issues.

1 participant