Merge remote-tracking branch tech/bus/peripherals into qcom-next

Author: sgaud-quic

Documentation/devicetree/bindings/i2c/qcom,i2c-geni-qcom.yaml

@@ -75,6 +75,7 @@ required:
 
 allOf:
   - $ref: /schemas/i2c/i2c-controller.yaml#
+  - $ref: /schemas/soc/qcom/qcom,se-common-props.yaml#
   - if:
       properties:
         compatible:

Documentation/devicetree/bindings/serial/qcom,serial-geni-qcom.yaml

@@ -12,6 +12,7 @@ maintainers:
 
 allOf:
   - $ref: /schemas/serial/serial.yaml#
+  - $ref: /schemas/soc/qcom/qcom,se-common-props.yaml#
 
 properties:
   compatible:

Documentation/devicetree/bindings/soc/qcom/qcom,se-common-props.yaml

@@ -0,0 +1,26 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/qcom/qcom,se-common-props.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: QUP Peripheral-specific properties for I2C, SPI and SERIAL bus
+
+description:
+  The Generic Interface (GENI) based Qualcomm Universal Peripheral (QUP) is
+  a programmable module that supports a wide range of serial interfaces
+  such as UART, SPI, I2C, I3C, etc. This defines the common properties used
+  across QUP-supported peripherals.
+
+maintainers:
+  - Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
+  - Viken Dadhaniya <quic_vdadhani@quicinc.com>
+
+properties:
+  qcom,enable-gsi-dma:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Configure the Serial Engine (SE) to transfer data in QCOM GPI DMA mode.
+      By default, FIFO mode (PIO/CPU DMA) will be selected.
+
+additionalProperties: true

Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.yaml

@@ -25,6 +25,7 @@ description:
 
 allOf:
   - $ref: /schemas/spi/spi-controller.yaml#
+  - $ref: /schemas/soc/qcom/qcom,se-common-props.yaml#
 
 properties:
   compatible:

drivers/i2c/busses/i2c-qcom-geni.c

@@ -870,7 +870,13 @@ static int geni_i2c_probe(struct platform_device *pdev)
 		goto err_clk;
 	}
 	proto = geni_se_read_proto(&gi2c->se);
-	if (proto != GENI_SE_I2C) {
+	if (proto == GENI_SE_INVALID_PROTO) {
+		ret = geni_load_se_firmware(&gi2c->se, GENI_SE_I2C);
+		if (ret) {
+			dev_err_probe(dev, ret, "i2c firmware load failed ret: %d\n", ret);
+			goto err_resources;
+		}
+	} else if (proto != GENI_SE_I2C) {
 		ret = dev_err_probe(dev, -ENXIO, "Invalid proto %d\n", proto);
 		goto err_resources;
 	}