Merge branch 'linux-5.15-trunk/at91/base_dt' into linux-5.15-mchp

Author: cristibirsan

Documentation/devicetree/bindings/arm/atmel-at91.yaml

@@ -126,6 +126,18 @@ properties:
           - const: atmel,sama5d3
           - const: atmel,sama5
 
+      - description: CalAmp LMU5000 board
+        items:
+          - const: calamp,lmu5000
+          - const: atmel,at91sam9g20
+          - const: atmel,at91sam9
+
+      - description: Exegin Q5xR5 board
+        items:
+          - const: exegin,q5xr5
+          - const: atmel,at91sam9g20
+          - const: atmel,at91sam9
+
       - items:
           - enum:
               - atmel,sama5d31

Documentation/devicetree/bindings/vendor-prefixes.yaml

@@ -191,6 +191,8 @@ patternProperties:
     description: B&R Industrial Automation GmbH
   "^bticino,.*":
     description: Bticino International
+  "^calamp,.*":
+    description: CalAmp Corp.
   "^calaosystems,.*":
     description: CALAO Systems SAS
   "^calxeda,.*":
@@ -395,6 +397,8 @@ patternProperties:
     description: Exar Corporation
   "^excito,.*":
     description: Excito
+  "^exegin,.*":
+    description: Exegin Technologies Limited
   "^ezchip,.*":
     description: EZchip Semiconductor
   "^facebook,.*":

arch/arm/boot/dts/Makefile

@@ -25,6 +25,7 @@ dtb-$(CONFIG_SOC_AT91SAM9) += \
 	usb_a9263.dtb \
 	at91-foxg20.dtb \
 	at91-kizbox.dtb \
+	at91-lmu5000.dtb \
 	at91sam9g20ek.dtb \
 	at91sam9g20ek_2mmc.dtb \
 	tny_a9g20.dtb \
@@ -40,6 +41,7 @@ dtb-$(CONFIG_SOC_AT91SAM9) += \
 	at91-kizboxmini-base.dtb \
 	at91-kizboxmini-mb.dtb \
 	at91-kizboxmini-rd.dtb \
+	at91-q5xr5.dtb \
 	at91-smartkiz.dtb \
 	at91-wb45n.dtb \
 	at91sam9g15ek.dtb \

arch/arm/boot/dts/at91-lmu5000.dts

@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Device Tree file for CalAmp LMU5000 board
+ *
+ * Copyright (C) 2013 Adam Porter <porter.adam@gmail.com>
+ */
+
+/dts-v1/;
+#include "at91sam9g20.dtsi"
+
+/ {
+	model = "CalAmp LMU5000";
+	compatible = "calamp,lmu5000", "atmel,at91sam9g20", "atmel,at91sam9";
+
+	chosen {
+		bootargs = "mem=64M console=ttyS0,115200 rootfstype=jffs2";
+	};
+
+	memory {
+		reg = <0x20000000 0x4000000>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		main_clock: clock@0 {
+			compatible = "atmel,osc", "fixed-clock";
+			clock-frequency = <18432000>;
+		};
+	};
+};
+
+&dbgu {
+	status = "okay";
+};
+
+&ebi {
+	status = "okay";
+
+	nand_controller: nand-controller {
+		pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
+		pinctrl-names = "default";
+		status = "okay";
+
+		nand@3 {
+			reg = <0x3 0x0 0x800000>;
+			rb-gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
+			cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
+			nand-bus-width = <8>;
+			nand-ecc-mode = "soft";
+			nand-on-flash-bbt;
+			label = "atmel_nand";
+			status = "okay";
+
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				kernel@0 {
+					label = "kernel";
+					reg = <0x0 0x400000>;
+				};
+
+				rootfs@400000 {
+					label = "rootfs";
+					reg = <0x400000 0x3C00000>;
+				};
+
+				user1@4000000 {
+					label = "user1";
+					reg = <0x4000000 0x2000000>;
+				};
+
+				user2@6000000 {
+					label = "user2";
+					reg = <0x6000000 0x2000000>;
+				};
+			};
+		};
+	};
+};
+
+&macb0 {
+	phy-mode = "mii";
+	status = "okay";
+};
+
+&pinctrl {
+	board {
+		pinctrl_pck0_as_mck: pck0_as_mck {
+			atmel,pins = <AT91_PIOC 1 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+		};
+	};
+
+	usb0 {
+		pinctrl_usb1_vbus_gpio: usb0_vbus_gpio {
+			atmel,pins = <AT91_PIOC 5 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+	};
+};
+
+&ssc0 {
+	status = "okay";
+	pinctrl-0 = <&pinctrl_ssc0_tx>;
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usart0 {
+	pinctrl-0 =
+		<&pinctrl_usart0
+		 &pinctrl_usart0_rts
+		 &pinctrl_usart0_cts
+		 &pinctrl_usart0_dtr_dsr
+		 &pinctrl_usart0_dcd
+		 &pinctrl_usart0_ri>;
+	status = "okay";
+};
+
+&usart2 {
+	status = "okay";
+};
+
+&usb0 {
+	num-ports = <2>;
+	status = "okay";
+};
+
+&usb1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb1_vbus_gpio>;
+	atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};