You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
Copy file name to clipboardExpand all lines: lasercutter.md
+44-12Lines changed: 44 additions & 12 deletions
Display the source diff
Display the rich diff
Original file line number
Diff line number
Diff line change
@@ -10,9 +10,9 @@
10
10
1. Intro
11
11
2. Equipment List
12
12
3. Getting Started
13
-
1. Requirements
14
-
2. Software and Setup
15
-
3. Using the Machine
13
+
1. Requirements
14
+
2. Software and Setup
15
+
3. Using the Machine
16
16
4. Safety
17
17
5. Booking
18
18
6. Common Issues
@@ -26,13 +26,17 @@ Laser cutters are an effective way to cut and engrave various materials, most co
26
26
# 2. Equipment List
27
27
28
28
All three of these pieces of equipment must be present and active during usage:
29
+
29
30
### 1. Laser Cutter: [xTool S1](https://www.xtool.com/products/xtool-s1-laser-cutter), with [40w diode laser module](https://www.xtool.com/products/xtool-s1-40w-laser-module) and [Riser Base](https://www.xtool.com/products/xtool-s1-riser-base).
31
+
30
32
31
33
32
-
This documentation will cover basic usage of the xTool s1 in the makerspace.
34
+
This documentation will cover basic usage of the xTool s1 in the makerspace.
33
35
34
36
You can see the range of current user support materials and guides from xTool [here](https://support.xtool.com/article/1106?from=learning-center).
37
+
35
38
### 2. Fire Suppression System: [xTool Fire Safety Set](https://www.xtool.com/products/fire-safety-set).
39
+
36
40
37
41
38
42
Make sure that the CO2 indicator is NOT flashing, before use of the machine. This indicates that the CO2 canisters have been used and need replacing. Please tell a relevant member of faculty if this is the case so it can be replaced before use of the machine.
@@ -42,7 +46,9 @@ The single-use fire safety set on top of the machine uses 4 large CO2 canisters
42
46
To manually trigger the fire suppression system if required, press the FRONT button once. This will activate the fire suppression.
43
47
44
48
For more information, the fire safety set user guide can be found [here](https://support.xtool.com/article/1145#qNpmX).
The xTool Smoke Purifier must be switched on at the back and the dial turned up so that it is in a working state before using the laser cutter. The tube coming out of the back must be positioned so that it points OUTSIDE of the building (through the window).
@@ -54,27 +60,34 @@ More information about the xTool Smoke Purifier can be found [here](https://supp
54
60
# 3. Getting Started
55
61
56
62
If you have not completed the CODE laser cutter training session and safety questionnaire, DO NOT attempt to use the machine.
63
+
57
64
### Requirements
65
+
58
66
To use the machine, you will need the following:
67
+
59
68
1. The key to the laser cutter (can be booked, see "5. Booking").
60
69
2. A laptop with xTool Creative Space software installed (download can be found [here](https://www.xtool.com/pages/software)).
61
70
3. A free USB type A port (or adapter).
62
71
4. A secondary person present in the room whilst the machine is active.
63
72
64
73
### Software and Setup
74
+
65
75
The [xTool Creative Space software](https://www.xtool.com/pages/software) requires an account to be made to verify that you have received the additional xTool training, which consists of a single video running through some basic safety information. You can run through this training by clicking the badge under your account name, otherwise it will trigger if you attempt to use the machine for the first time.
66
76
67
77
Upon completing the xTool training, you will receive a digital certificate. You may download this if you wish.
68
78
69
79
Click on "New Project" in the top right of the application. It may guide you through a basic tutorial. More tutorials can be found on YouTube, such as [this one by Creative Ramblings](https://www.youtube.com/watch?v=1N66RNpKtDc) if you wish to see more examples.
70
80
71
81
Once you have verified that:
82
+
72
83
1. The fire safety set does NOT have a CO2 warning
73
84
2. The ventilation is turned on with the exhaust facing OUTSIDE of the building
74
85
3. There is no damage to the laser cutter or lid
86
+
75
87
you may switch on the laser cutter and plug the USB A cable into your laptop.
76
88
77
89
### Using the xTool s1
90
+
78
91
The xTool s1 will not work without the physical key. The key can be booked as required. (see "5. Booking")
79
92
80
93
The machine's on and off switch can be found at the back of the machine on the right, as well as the key slot. You will also find an emergency off switch on the right hand side.
@@ -84,28 +97,47 @@ The machine uses loud beeps to indicate recognition of change (e.g.: turning on,
84
97
The honeycomb plate must be placed inside the machine, positioned all the way to the right, and all the way to the front.
85
98
86
99
1. Connect the Machine:
87
-
Once the xTool s1 is plugged into your laptop, the software should recognise it. If it does not automatically connect, click the connection button on the right and select the machine from the list.
100
+
Once the xTool s1 is plugged into your laptop, the software should recognise it. If it does not automatically connect, click the connection button on the right and select the machine from the list.
88
101
89
102
2. Position Material and Laser:
90
-
You may place your desired material on top of the honeycomb plate, and position the laser head by hand so that it is somewhere on top of the material, indicated by the red + guiding laser. You will see that the software will update to the same location.
103
+
You may place your desired material on top of the honeycomb plate, and position the laser head by hand so that it is somewhere on top of the material, indicated by the red + guiding laser. You will see that the software will update to the same location.
91
104
92
105
3. Change Settings:
93
-
You can select the same material inside the software, which will change the speed and power of the laser during cuts, scoring and engraving.
106
+
You can select the same material inside the software, which will change the speed and power of the laser during cuts, scoring and engraving. Feel free to play around with these values, but for safety reasons it's best to start with a lower power and medium speed, and if it is not enough then you can do multiple passes.
94
107
95
108
4. Auto Measure Material Height:
96
-
Close the lid and click the auto measure button at the top to probe the height of the material at the location of the guiding laser.
109
+
Close the lid and click the auto measure button at the top to probe the height of the material at the location of the guiding laser.
97
110
98
111
5. Verify Placement of the Design:
99
-
Position your design as required, then click "framing" to send a preview job to the laser cutter. Press the button on the front of the machine to see a traced rectangular outline of where the laser cutter will operate.
112
+
Position your design as required, then click "framing" to send a preview job to the laser cutter. Press the button on the front of the machine to see a traced rectangular outline of where the laser cutter will operate.
100
113
101
114
6. Confirm and Start Job:
102
-
Adjust the design as needed, and once you are happy with the framing, click start, then press the button on the front to begin laser cutting.
115
+
Adjust the design as needed, and once you are happy with the framing, click start, then press the button on the front to begin laser cutting.
103
116
104
117
7. Finish and Tidy:
105
-
Once the machine has stopped fully, wait until the internal fans stop and the smoke is clear, then open the lid and remove your finished cut. Remove all debris that may have dropped through the honeycomb plate, turn off the machine and purifier, and return the key.
118
+
Once the machine has stopped fully, wait until the internal fans stop and the smoke is clear, then open the lid and remove your finished cut. Remove all debris that may have dropped through the honeycomb plate, turn off the machine and purifier, and return the key.
106
119
107
120
# 4. Safety
108
121
122
+
Some materials are NOT safe to laser cut. Always check that you know what material you are using, and that it will not produce any toxic fumes.
123
+
124
+
### Fires
125
+
126
+
Some very small fires will go away on their own or with a light blow. Opening the lid and blowing it out manually will automatically stop the laser.
127
+
128
+
In the case of a small->medium fire, use the fire safety box located on top of the machine. Press the button on the front of the fire safety box once to trigger two bursts of CO2.
129
+
130
+
If a fire does not go out with the fire safety box, or it is not safe for you to use it, use a fire extinguisher. If it gets out of control, pull the fire alarm and inform a member of faculty as soon as possible.
131
+
132
+
After any fire or damage to the machine, inform a relevant member of faculty and cease any use of the machine before it is inspected by a professional.
133
+
134
+
Never leave the room whilst using the machine.
135
+
136
+
Never use the machine without someone else present in the room. If they leave, pause the job.
137
+
138
+
# 5. Booking
139
+
140
+
Booking the machine is currently not possible. Please talk to Daniel Buzzo if you would like to use the machine before a booking system is implemented.
0 commit comments